Next:
Contents
QuickFlick-II Build manual
Contents
1. Preface
1.1 Introduction
1.2 About the Designer
1.3 Build Options
2. Preparation
3. Tail
3.1 Kit Parts Required
3.2 Additional Parts Required
3.3 Preparation notes
3.4 Build Notes
3.4.1 Boom cutting
3.4.2 Vertical Stabilizer and Rudder preparation
3.4.3 Tape hinging the vertical stabilizer
3.4.4 Horizontal stabilizer and elevator
3.4.5 Horizontal stabilizer bonding to boom
3.4.6 Vertical stabilizer bonding to boom
4. fuselage
4.1 Kit Parts Required
4.2 Additional Parts Required
4.3 Preparation Notes
4.4 Build Notes
4.4.1 fuselage side preparation
4.4.2 Formers
4.4.3 Wing mount crossbeam doublers
4.4.4 Lower deck
4.4.5 Boom mount blocks
4.4.6 Fuselage reinforcements
4.4.6.1 Vertical reinforcements
4.4.6.2 Horizontal reinforcements
4.4.7 Joining the boom to the fuselage
4.4.7.1 Preparation
4.4.7.2 Joining Process
4.5 Summary
5. Wing
5.1 Dihedral braces
5.2 Wing bolt blocks
5.2.1 Leading block
5.2.2 Trailing block
5.3 Main wing construction
5.3.1 Ribs to TE, spars and bottom sheeting
5.3.2 Frontal webbing
5.4 Shaping wing trailing edges
5.5 Assembling two wing halves with dihedral brace
5.6 Adding half ribs and leading wing mount block
5.6.1 First set of half ribs
5.6.2 Leading wing bolt block
5.6.3 Second set of half ribs
5.7 Adding top D box sheeting
5.8 Adding rear webbing
5.9 Adding Leading edge
5.10 Adding Wingtips
5.11 Adding wing gussets
5.12 Dihedral brace center sheeting and finishing
5.13 Applying Carbon Fiber tow to the wings
5.14 Drilling wing bolt holes
5.14.1 Leading side wing bolt
5.14.2 Trailing side wing bolt
5.15 Drilling fuselage wing bolt holes
5.15.1 Primary hole in crossbeam F6
5.15.2 Secondary hole in located in crossbeam F7
5.16 Finishing
5.16.1 Shaping the leading edge
6. Nose block and canopy
6.1 Nose block
6.2 Canopy
6.3 Shaping
6.4 Securing the Canopy
7. Control Rod and Horn Installation
7.1 Control horn installations
7.1.1 Rudder control horn installation
7.1.2 Elevator control horn installation
7.2 Control wire and tube installation
8. Servo installation
9. Covering
10. Peg Installation
11. Optional Enhancements
11.1 Rear fuselage fairing
11.2 Fiber glassing (A
DVANCED
)
11.2.1 Fuselage Glassing
11.2.2 Canopy Glassing
12. Final Assembly
13. Flying
13.1 Setting the Center of Gravity
13.2 Test gliding
14. Appendix
14.1 Making support tubes / sheaths
14.1.1 Introduction
14.1.2 Requirements
14.1.3 Procedure
14.2 Common product names
14.3 Commonly used Terms and Acronyms
14.4 Conversions
14.4.1 Lengths and sizes
14.4.2 Weights
14.5 Further information
Index
About this document ...
Next:
Contents
Paul Daniels
2005-09-15
